Resetting an error on a Siemens washing machine

Resetting an error on a Siemens washing machine Some washing machines are immediately ready for use after the breakdown has been repaired. The system automatically records that the problem has been resolved, the part is working properly, and there is no longer any need to display a warning. On Siemens the scheme is different - here after repair you will have to manually reset the error, otherwise the machine will not start the wash. It remains to understand how to reset the error on a Siemens washing machine. We offer step-by-step reset instructions and an overview of common faults.

Getting rid of unnecessary errors

The self-diagnosis system on modern Siemens works properly - it immediately notices a failure and displays the corresponding error code on the display. But after fixing the problem, the user must inform the board that the repair is complete. In simple words, you need to manually reset the signal combination. The algorithm for restarting the self-diagnosis system depends on the Siemens model. However, the difference is insignificant. As a rule, it is enough to do the following: how to reset an error on Siemens

turn the program selector to position “0”;
move the programmer one more division to the left;
hold down the “Start” button for 2-3 seconds;
Scroll the selector to the starting position.

Sometimes you need to reset an error on Siemens several times - the system takes a long time to process the command.

If everything is done correctly, then after a while the error will be reset and the machine will be ready for use. Sometimes the system does not accept the command for a long time - you need to repeat the procedure 2-3 times. On some Siemens models, instead of “Start” you should press “Spin”. It is better to clarify the sequence of actions in the factory instructions.

Typical fault codes

The database of the Siemens self-diagnosis system includes dozens of different codes, which allows the user to be informed of the location and nature of the breakdown. But most of the introduced combinations remain in the “shadow”: the components and mechanisms related to them rarely fail. Basically, a certain set of encryption codes are displayed - typical brand faults.

F01 Indicates a leaky drum. Perhaps the hatch is not closed properly or something is stuck between it and the hull. It is necessary to check the door, it is better to pack the laundry.
F02 Signals that water is not being filled into the machine. This happens if the central water supply is blocked or turned off, the inlet hose is clogged, or the inlet filter mesh is clogged. Sometimes problems with the dial are caused by a faulty pressure switch and a failure in the control board.
F03 Error in the drainage system - water was not pumped out of the tank within 10 minutes. It is necessary to consistently check all key drainage elements for blockages and damage: debris filter, impeller and pump. It is also recommended to ring the pump, and if the resistance is not 200 Ohms, then replacement is indicated. Lastly, the control board is tested.

A typical malfunction of Siemens washing machines is error code F03: problems with draining water from the tank.

F05 Malfunctions in the engine operation have been recorded - it does not start, does not gain the required power, or, on the contrary, spins up above normal. The repair plan depends on the cause of the problem. Sometimes the only thing left to do is replace the motor.
F06 The water does not heat up to the required degrees. The thermistor, temperature sensor, the heating element itself or the wiring connected to it have probably failed.
F14 Power problems. Lights up if the voltage in the network is unstable and falls below 172V.It is necessary to normalize the current supply by connecting a stabilizer to the network or adjusting the power supply.
F17 Flood time exceeded. There can be three reasons: the water supply tap is turned off, the inlet filter mesh is clogged, or the pressure in the water supply has dropped below 1 bar. It is necessary to establish a water supply, after which the washing will be restored.
F18 Drain waiting time exceeded. In simple words, the drum did not have time to empty within the time specified by the program. The cycle is reset after 1.5 minutes of waiting, after which the machine gives an error and freezes. The problem is a breakdown of the pump, pressure switch or control board. Repair involves cleaning the drainage system and replacing faulty components.
F19 Heating timeout exceeded: the heating system has failed. As a rule, the heating element does not work at all, or a high voltage is detected in the electrical network. Sometimes the problem is the absence of a thermostop: the accumulated temperature exceeds the norm and threatens to overheat the machine. To correct the situation, it is necessary to check the heater and the entire circuit as a whole, and if necessary, replace the components. With this error, Siemens does not freeze, but continues washing in cold water.
F23 The Aquastop system has activated. The sensor has leaked or broken.
F57 The control board has flown. Requires professional diagnostics, repair or firmware.

The self-diagnosis system greatly simplifies the use and repair of Siemens. The main thing is to correctly decipher the code, completely eliminate the breakdown and reset the error.