Indesit washing machine displays error F07

Indesit washing machine displays error F07 The self-diagnosis system greatly facilitates the operation of the washing machine. So, if error F07 is displayed on Indesit, it means that there is a problem with water intake. In simple words: the machine cannot fill the drum to the required level in the specified time. Models without a display will indicate this problem with an indication: “Soaking”, “Extra Rinse” and “Revolutions” will flash, or “Revolutions”, “Super Wash” and “Fast” will flash at the same time. It will not be possible to ignore the “dryness” of the equipment - you will have to carry out diagnostics and eliminate the failure.

Potential problems

An empty Indesit washing machine will not wash clothes. Moreover, the cycle will not start - the machine will buzz and give an error. Code "F07" does not always indicate a serious breakdown: sometimes the problem is the lack of central water supply or a loose door. In the first case, it is impossible to draw water, in the second, the board blocks the supply for safety reasons.

If there is water in the riser and the hatch is tightly locked, it means that the washing machine issues code F07 due to a malfunction. Several malfunctions can lead to an error, from a blockage in the filling system to a broken pressure switch and a failed control board. Let's look at each possible culprit.

Inlet valve. This element is part of the filling system, opening the “entrance” for water into the machine. If it breaks, the membrane does not work and the machine remains “locked”. You can guess that there is a problem with the valve mechanism by not rinsing out the detergent from the powder receptacle. The guess is also verified by a test during which 220V is supplied to the valve. If the device does not click in response, then a fault has been detected.
Mesh filter. Error F07 can also be caused by a simple blockage of the filling system. As a rule, the filter mesh installed at the end of the hose becomes dirty. Small holes become clogged with dirt, debris and scale, Indesit tries to draw water, buzzes for several minutes, but to no avail - the drum remains empty.
Coarse filter. Another mesh installed in a water pipe for primary water purification. The filter takes all the “impact” on itself, over time it becomes clogged with dirt and makes typing difficult. The problem can be easily fixed by cleaning the nozzle.

Code F07 on Indesit washing machines indicates problems with water supply!

Pressostat. More often, problems with filling occur due to a faulty level sensor. This device fails and ceases to detect the degree of fullness of the drum. The board notices the incorrect operation of the pressure switch and, in order to prevent leakage, urgently stops the program. To check the device, you need to remove the top cover from the Indesit, find the sensor, unhook the tube from it and blow it out. Normally, the mechanism should close and clicks will be heard; if it breaks, there will be silence.
Pressostat hose. Over time, the pipe can become dirty, damaged and leaky. All this prevents the normal operation of the level sensor, makes it impossible to fill the drum and leads to error F
Inlet hose. Probably, the hose coming from the riser is pinched, and the water cannot “reach” the drum.
Drainage pump. Before a new cycle, any Indesit washing machine empties the tank from the previous wash by draining the water. If problems arise with draining, the board detects a drum failure and cancels the program.
Control board. If a module fails, the entire system will stop.The electronic unit will not be able to receive or transmit information, therefore, at the stage of drawing water, the machine stops and error F07 is displayed.

Even a professional cannot tell right away what the F07 combination means. The listed breakdowns often have similar “symptoms”, especially if it was not possible to evaluate the behavior of the machine before the failure. To identify the problem, you will have to sequentially check all possible problems, moving from the simple, hose, filters and pressure switch, to the complex - the control board.

How to find a breakdown?

If you notice code F07 on the display, you do not have to immediately contact service. Anyone can carry out diagnostics and repairs with their own hands, the main thing is to act consistently and follow safety precautions. First of all, we disconnect Indesit from communications, and secondly, we begin checking the filling system of the machine. We proceed like this:

see if the central water supply is turned off (just open the tap in the bathroom);
make sure that the water supply tap is open;
assess the condition of the inlet hose (is there any damage, pinching or blockage).

Next in line is the filter mesh. This is a round nozzle that attaches to the inlet hose, collecting dirt and debris from the water supply. It is necessary to check whether the filter is completely clogged. The instructions on what to do to diagnose and clean the mesh are as follows:

Be careful when disconnecting the inlet hose - there may be water left in it!

loosen the clamp securing the inlet hose to the Indesit body;
disconnect the hose from the washing machine;
at the junction we look for a grid;
we cling to the protruding part of the filter and remove it from the grooves;
we wash the mesh under the tap, if necessary, clean it with a toothbrush and laundry soap;
install the filter in place and return the inlet hose to the housing.

Another reason for an empty drum is a clogged coarse filter. It is more difficult to clean, since it is built into the water supply and is located behind the water supply tap. You will have to use wrenches to unscrew a couple of fasteners on the riser and loosen the nut holding the valve. A stream will immediately flow out of the hole, which will wash away the dirt on the mesh.

Intake mechanism

More often, code F07 on Indesit washing machines indicates problems with the inlet valve. Most likely it is broken and needs to be replaced. The part cannot be repaired - it is “disposable”. Fortunately, the new device is inexpensive and will cost 700 rubles. Provided that the repair is done independently, the service center will charge about 2 thousand rubles for such work. Testing and replacing the valve on an Indesit washing machine is easy if you proceed as follows:

disconnect the washing machine from the power supply and water supply;
disconnect the inlet hose from the Indesit and drain the residual water from it;
unhook the top cover;
find the fill valve;
take a photo of how the wires and hoses are connected;
disconnect the supplied wiring and pipes;
loosen the fixing screw;
remove the valve;
install a new valve in the “socket”;
secure the device with a bolt, connect hoses and wiring;
return the cap and inlet hose.

After replacement, we check the functionality of the new valve - turn on the washing machine and start the wash. If error F07 appears again, then the problem is in the board. In this case, it is dangerous to look for the problem yourself; it is better to contact the service.