Error F13 on Ariston washing machine

Error F13 on Ariston washing machine You won’t find error code F13 on budget washing machines from Ariston: this combination signals a problem with the drying function. This simplifies the decoding process and allows you to quickly localize the affected area. The difficulty is that there is little information in the public domain on how to deal with F13 on Aristonov assault rifles. We propose to fill this gap, decipher the error and consider options for its repair.

Manifestation of the cipher

Thanks to the self-diagnosis system, the Ariston washing machine will automatically detect problems with drying and inform the user with a code or indication. Displaying it on the display is easier - the washing machine will pause operation and display the appropriate combination. A forced stop can occur at any stage of the cycle:

the equipment issued “F13” when turning on the program and canceled the start of the wash;
the machine washed, but when drying started, it showed an error and refused to dry the clothes;
the machine started drying, but after a certain time it issued a code and froze.

Error F13 may appear before or during drying - it all depends on the cause of the problem.

If the model does not have a display, the self-diagnosis system will report a problem through an indication - flashing lights. The frequency and amount of glow depends on the Ariston brand.

Ariston Margherita type AL 108D and AL 128D. These “oldest” machines in the model range of the manufacturer have only two light bulbs - power and drying. If there is a problem with the latter, the machine will start producing 13 quick flashes with a break of 7-15 seconds. At the same time, the programmer will also work, clicking and rotating counterclockwise.
Ariston AML 105 and 109 series.On these washing machines, when there is a problem with the drying function, three LEDs blink, indicating additional options. Only the second one from the bottom, usually “Quick Wash,” will remain turned off. The “Key” will also blink constantly.
Hotpoint-Ariston Low-End brands ARM XXL, CA WD and AV DK. Here the machine responds to F13 by flashing the temperature LEDs. Again, all except the second one are highlighted. The names of the “lights” on the instrument panels differ, but, as a rule, the trinity “No heating”, “40”, “50” is on.

If the dryer and washing machine issued F13, then there is no need to panic. It is better to first try to interpret the combination and clarify the nature of the problem. Let's figure out what might break next.

Let's explain the code

To understand how to fix F13, you need to take a closer look at the error. So, this combination on Ariston and Hotpoint-Ariston indicates problems with drying. More precisely, a code is displayed when the temperature sensor is faulty. There are two options: either the thermostat is broken, or a short circuit has occurred. In any case, the board stops controlling the heating, the drying cycle is canceled for safety reasons, and a code is displayed on the display. sensor check

It turns out that F13 directly indicates a malfunction of the temperature sensor. It is impossible to more accurately determine the nature and scale of the problem, identify the causes and carry out appropriate repairs without special equipment. Often the user sees no reason to worry, since the device, when called a multimeter, produces acceptable values of 18-20 kOhm. However, at the slightest movement due to vibrations during operation of the machine, the thermostat moves, goes into a break and stops functioning. In such cases, it is advisable to immediately connect a service center.

A working temperature sensor in normal mode should produce values of 18-20 kOhm.

Self-diagnosis is possible, but only in some situations.

What to check first?

If error F13 is displayed for the first time, then it is possible that a one-time failure of the control unit or display system has occurred. You can take a chance and restart the machine: turn off the washing machine from the network, wait 10-20 minutes, and then start the interrupted mode and observe the behavior of the equipment. The reappearance of the code will indicate a malfunction of the temperature sensor.

It is strongly not recommended to deal with the breakdown of the F13 on your own. It is better to immediately contact the service center and let the repairmen carry out diagnostics using special equipment. Otherwise, there is a high probability of aggravating the problem, even to the point of “fatal outcome” of the equipment.

Home repairs are allowed only if the user knows how to operate the electronics of an Ariston washing machine. Then you can check whether the contacts are securely fastened in the terminals in the area from the temperature sensor to the electronic controller. It is likely that the vibration emanating from washing led to loose connections between the wires.

If F13 did not appear due to a one-time failure and loose wiring, then you will not be able to repair the machine yourself - professional repair is necessary.

Fault options

When the Ariston washing machine cannot cope with drying things+ and issues F13, in 70% of cases the temperature sensor is “to blame”. The device fails after a break or short circuit. The only way to solve the problem is to replace the faulty part. The control module has failed

In the remaining 30%, other problems lead to the error.

Module firmware failure.In simple words, the board “forgets” the factory algorithm and is no longer capable of executing the embedded programs. To fix the problem, you need to reprogram the electronic unit. Possible flashing only on special equipment.
Board failure. Another option is that the control module is broken. For example, the so-called tracks were damaged, resistors burned out, and the controller was damaged. The nature of the malfunction will determine what to do during repairs: restore contacts, replace radio elements or install a new unit.
Damaged wiring. The wires leading from the drying sensor to the control module may have broken due to vibrations or rodents. In any case, the connections must be restored by changing the conductors.

It is prohibited to twist or solder the wiring on washing machines - such connections are unreliable and dangerous!

It is worth mentioning that error F13 on Ariston dryers occurs frequently. This is due to the ill-conceived design of the machine, on which the inlet hose is located directly above the board. In the event of a leak or heavy condensation, moisture enters the module, which inevitably leads to burnout of the latter. Therefore, it is not recommended to purchase dryers from this manufacturer. It is better to look for alternative options that are more durable and safe.