How to use a Bosch Maxx 4 washing machine

You can find out how to use the Bosch Maxx 4 washing machine from the instructions for the equipment. Before installing and starting the machine, read the manual. It says how the equipment is connected, how the first launch is performed, and describes the main modes programmed in the intellect. By following the recommendations, you will put the washing machine into operation correctly.

“Re-preservation” and installation of the machine

When the machine arrives from the store, let it sit for a couple of hours. The washing machine must accept the room temperature. You can then carefully remove the packaging from the device.

If possible, it is better to entrust the installation and connection of the washing machine to specialists.

If you are confident in your own abilities, you can connect the machine yourself. Check with the store to see if installing the washing machine yourself will affect the warranty. Sometimes in this case the right to free service “burns out”.

Once the machine has settled, you can begin installation. Be sure to remove the shipping bolts that secure the drum during transportation. If this is not done, the washing machine may fail upon first startup.

Information on the number and location of transportation bolts is given in the instructions. After removing the fasteners, insert plastic plugs into the resulting holes - they come with the washing machine.

What other rules should you follow when installing an automatic machine?

• The washing machine should only be placed on a hard, level surface.
• Be sure to level the device - the height of the case is adjusted using the legs.
• Provide a gap of at least 2-2.5 centimeters between the side walls of the case and the furnishings. A gap of 5-6 cm should be left at the back of the machine.
• The SMA hatch must open 180 degrees freely.

It is recommended to place a special rubber mat under the machine that absorbs vibrations. Then the washing machine will be even quieter. You can buy anti-vibration cloth at hardware stores.

Connect the hoses and power cord

The Bosch Maxx 4 washing machine is connected only to cold water supply. An inlet hose for connecting the washing machine to the communications is included in the kit. It is important to install the device at a permissible distance from the water pipe so that the length of the filling pipe is sufficient.

A shut-off valve is always provided in front of the inlet hose. The tap will provide the ability to shut off the water supply to the machine if necessary. Next, check the joints for leaks. This will prevent leaks during further operation of the device.

Afterwards the washing machine is connected to the sewerage system. There are three valid connection options:

• lower the other end of the drain hose into the bathtub or sink;
• connect the corrugation to the siphon fitting;
• install the drainage hose directly into the sewer pipe.

The drain hose should be located at a certain bend, at a distance of 60-100 cm from the floor level.

The standard length of the drain hose of an automatic machine is one and a half meters. If this is not enough for you, you should not “increase” the corrugation. It is better to purchase a one-piece hose of the required size and connect the washing machine through it.

An equally important nuance is connecting the SMA to electricity. For an automatic machine, it is necessary to provide a separate moisture-resistant socket with grounding.The point should be located 60 cm from the floor level or higher.

The minimum height of 60 cm is due to safety precautions. This way, in case of leaks, it will be possible to avoid water getting into the outlet. Therefore, there will be no short circuit in the network.

The socket for the washing machine must be connected to a separate machine through a residual current device. The wiring must be designed for the load created by the machine, with a small margin. The instructions for SMA Bosch Max 4 prohibit the use of extension cords to connect the device to the network. The machine must be plugged into a power outlet directly.

Let's start washing

Having installed the “home assistant” and connected it to communications, you can start washing. The first start of the machine is carried out empty - without things in the drum, but with a cleaning agent. This is necessary to wash the inside of the machine from dirt, dust, and technical fluids.

After the first start, you can turn on the “Rinse” cycle again. Next, wipe the drum with a clean damp cloth. Only now is it allowed to load laundry into the machine.

Next, sort the items by color, type of fabric, intensity of contamination, and permissible temperature exposure. Fasten buttons and zippers, remove all decorative elements that can be removed. Place socks and underwear in special laundry bags.

The further algorithm of actions will be as follows:

• open the washer hatch, make sure the drum is empty;
• load a batch of laundry into the machine;
• pour the detergent into the powder receptacle;
• turn on the machine, use the programmer to select the desired washing mode;
• adjust the cycle parameters if necessary (change the temperature, spin speed, add soaking or additional rinsing, etc.);
• start the wash by pressing the “Start” button.

Be sure to take into account the maximum permissible load weight. If the machine is designed for 6 kg of things, it is important to comply with this norm and not exceed the permitted value. As for laundry detergents, they must be marked “Automatic”.

Having finished washing, the automatic machine will emit a sound signal. Remove the laundry from the drum and wipe its walls with a dry cloth. Also, excess moisture is removed from the rubber cuff. It is important to leave the washing machine with the hatch and powder receptacle open so that it can be ventilated.

Selecting the appropriate washing algorithm

To care for different fabrics, the Bosch Maxx 4 CMA provides several washing algorithms. A description of all programs is presented in the equipment instructions. We'll tell you what modes this machine has.

• White laundry 90°C. Program for washing cotton. The water warms up to 90 degrees.
• Intensive 60°C. The mode is designed for heavily soiled cotton items.
• Colored items 30°C, 40°C, 60°C. A program for caring for durable cotton and linen items at different degrees of water heating.
• Synthetics 30°C, 40°C, 60°C. Algorithm for synthetic and mixed fabrics.
• Delicates 30°C. A mode that provides gentle washing. Suitable for “capricious” fabrics: silk, lace.
• Wool 15°C, 30°C. Mode for washing woolen items.

Washing modes are switched using a rotary programmer located on the dashboard.

Using the buttons on the dashboard, you can connect auxiliary options to the cycle, such as:

• quick wash (reduces cycle time);
• additional rinse;
• soak.

Also, using the buttons on the device, you can adjust the spin speed or turn it off completely.Information on the duration of each washing mode is in the instructions for the SMA. Thus, the duration of the cycle can vary from 45 minutes to 2.5 hours.

Reader comments

• Share your opinion - leave a comment