How to remove the cuff from the drum of a Samsung washing machine?

How to remove the cuff from the drum of a Samsung washing machine To save on repairs, many washing machine owners try to repair the equipment themselves. In fact, in most cases, you can restore “life” to the washing machine at home. The exception will be work that requires special equipment, experience and knowledge. For example, if the problem is in the control unit, then it is better to call a technician. If there is a need to replace the seal, you can try to do it yourself. Let's figure out how to remove the rubber seal from the drum and put a new cuff in its place, what the sequence of actions will be.

Remove the clamp from the outside

The seal is removed in two stages. Before proceeding with any actions, be sure to turn off the power to the equipment. First of all, you need to remove the outer clamp, which is a ring with a steel spring. To remove it, you need to use a slotted thin screwdriver to pull out the cuff, pry the clamp near the spring and slightly pull it in your direction.

Almost all Samsungs have a metal clamp, equipped with a spring latch. It is this spring insert that should be slightly stretched while simultaneously removing the ring. However, there are Samsung models whose cuff is fixed with a plastic clamp. There is no spring here; such a ring is much easier to remove due to the convenient plastic latch. When the outer clamp is removed from the housing, it is necessary to insert the rubber seal into the drum. In this position, the cuff will not interfere with further actions. remove the outer clamp

Removing the clamp from the inside

To remove the cuff from a Samsung washing machine, you must also remove the internal clamp that secures it. There should also be no difficulties at this stage of work. The algorithm will be like this:

remove the top cover of the MCA by unscrewing the two bolts holding it;
loosen the retaining ring with the existing fastening bolt. The screw should be unscrewed until the clamp can be removed without problems;
pull the seal together with the metal ring out of the housing.

If the purpose of removing the cuff was to clean it, then you should rinse the elastic band thoroughly using disinfectants. You don’t have to buy household chemicals, but use proven folk remedies.

It is important to “refresh” not only the seal, but also the place where it is installed.

All recesses of the drum that were previously covered with an elastic band are wiped. Typically, dirt and debris accumulate in such places, and mold may form.

Removing the façade of the building

If the goal was to replace the seal, you will have to remove the front panel of the Samsung washing machine. This is necessary to gain access to the inside of the drum, to securely fix the cuff in the body.

Using a screwdriver or screwdriver, unscrew the screws located on the front of the machine. Three bolts are located in the lower area of the wall; finding them is not difficult. The upper fasteners are covered by the control panel - you will have to disconnect this part and put it aside. remove the front part of the case

The last bolt is located under the powder receptacle. When all the screws are unscrewed, all that remains is to disconnect the front wall of the case and move it to the side. This will give you direct access to the drum.

Experienced craftsmen change the seal without removing the front panel, thereby saving time on repairs.However, installing the gasket from the inside is much more difficult, so it is better to still gain access to the drum.

We install a new part

Installing a new seal is an important stage of work. It is necessary to install the cuff correctly to ensure the tightness of the system and prevent water from leaking from under the hatch door. The algorithm for subsequent actions will be as follows:

insert the elastic band together with the internal clamp into the washer, put them on the drum ledge;
insert the sealing gasket and the metal retaining ring in a circle;
make sure that the inner clamp is inserted around the entire circumference;
tighten the fixing screw completely;
straighten the outer side of the cuff along the front part of the MCA;
Reinstall the outer clamp.

When the elastic band is straightened, you can begin reassembling the washing machine body. First, the front wall is mounted, secured with bolts, then the control panel is fixed, and the detergent dispenser is put back. Then you can attach the top cover. Once the Samsung washing machine is assembled, you need to run a test wash and see if a leak appears from under the drum door.